Ford Kuga

 Service Manual

Front Drive Halfshafts
Front Halfshaft LH (14 320 0)

Special Tool(s) / General Equipment

	204-159 Lever, Wheel Knuckle
	204-602 Installer, Halfshaft
	204-605 Separator, Lower Arm Ball Joint
	204-609 Protection Cap, Ball Joint Gaiter
	205-071-01 Adapter for 205-071 (Thrust Pad)
	205-775 Protector, Halfshaft Seal
	211-020 Separator, Ball Joint
	308-782 Remover, Driveline
Puller
Tire Lever

Removal

1. NOTE: This step is only necessary when installing a new component.

2. Refer to: Lifting (100-02 Jacking and Lifting, Description and Operation).

Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

3. NOTE: This step is only necessary when installing a new component.

WARNING: Make sure that no load is placed on the brake hose.

8. If equipped.

CAUTION: Make sure that the ball joint ball does not rotate.

10. Special Tool(s): 211-020

12. Special Tool(s): 204-605

14. Install the Special Tool(s): 204-609

16. If equipped.

Vehicles with 6-speed manual transaxle (MMT6)

WARNING: Be prepared to collect escaping fluid.

1. General Equipment: Tire Lever

2. Install the Special Tool(s): 205-775

Vehicles with 6-speed manual transmission (M66)

WARNING: Be prepared to collect escaping fluid.

1. Install the Special Tool(s): 308-782

2. General Equipment: Tire Lever

3. Remove the Special Tool(s): 308-782

4. Install the Special Tool(s): 205-775

Vehicles with automatic transaxle

19. General Equipment: Tire Lever

All vehicles

20.CAUTIONS:

• The inner constant velocity (CV) joint must not be bent more than 18.
• The outer constant velocity (CV) joint must not be bent more than 45.

Special Tool(s): 204-159, 204-605

NOTE: This step is only necessary when installing a new component.

Special Tool(s): 205-071-01 General Equipment: Puller

Installation

1. NOTE: This step is only necessary when installing a new component.

Special Tool(s): 204-602 Torque: 45 Nm

2. NOTE: Make sure that a new component is installed.

3. CAUTIONS:

• The inner constant velocity (CV) joint must not be bent more than 18.
• The outer constant velocity (CV) joint must not be bent more than 45.

1. Special Tool(s): 204-605

4. Special Tool(s): 204-159

5. Remove the Special Tool(s): 205-775

4. Torque: 90 Nm

5. Special Tool(s): 204-605

6. Remove the Special Tool(s): 204-609

8. Torque: 83 Nm

WARNING: Make sure that a new nut is installed.

CAUTION: Make sure that the ball joint ball does not rotate.

Torque: 80 Nm

10.NOTE: This step is only necessary when installing a new component.

NOTE: Only tighten the nut finger tight at this stage.

11. If equipped.

Torque: 8 Nm

12.Torque: 5 Nm

14.Torque: 120 Nm

17. If equipped.

18. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

19. Lower the Vehicle.

20.NOTE: This step is only necessary when installing a new component.

Torque: 270 Nm

Front Drive Halfshafts

Front Halfshaft LH (14 320 0)

Front Halfshaft RH - LHD 4WD/RHD 4WD

Inner Constant Velocity (CV) Joint Boot (14 336 0)

Outer Constant Velocity (CV) Joint Boot

Halfshaft Bearing